Pattern Corrections

All of our patterns are edited by a professional tech editor. Nevertheless, errors do occasionally slip through. Following are corrections to Basix patterns. If these errors do not appear in your version, then you have a revised edition; the revision date is listed on the lower right-hand corner of the last page of the pattern. If you think you may have found an error that is not listed here, please email us through our Contact page.

101 – Concord Top-Down Cardigan: Under Finished Measurements, the last 4 sizes are 58.75, 63.25, 67.5, 71.5)”. On page 2, under Back, JOIN SIDES, work even until piece measures 5.5 (5, 5.5, 5.75, 5.75, 6, 6.25, 5.5, 5.25, 5, 5)” from the beginning. Under Shape Gusset and Armholes, the note should read: Gusset and armhole shaping will be worked at the same time; please read entire section through before beginning. “Gusset shaping will not be completed until several inches before the bottom edge. Body will be joined when armhole shaping is complete.” The Armhole Shaping Row should read as follows: Armhole Shaping Row (RS): Increase 1 st each side this row, then every other row 2 (4, 4, 5, 5, 4, 2, 8, 8, 9, 7) more time(s), as follows: K1, M1-R, knit to last st, M1-L, k1. Purl 1 row. CO 2 sts at beginning and end of next 0 (0, 1, 1, 2, 3, 5, 3, 4, 5, 7) RS row(s). NOTE: If your row gauge matches the given gauge, and you have worked to the exact measurements given, you should have 80 (90, 96, 104, 114, 120, 128, 136, 146, 154, 160) sts for Back after armhole shaping is complete. However, due to differences in row gauge and measuring, you may find that you have a few sts more or less than these st counts. Purl 1 row. When armhole shaping is complete, break yarn, place sts on waste yarn, and set aside. Under Body, JOIN FRONTS AND BACK, you will have 156 (180, 202, 224, 246, 268, 290, 314, 338, 362, 384) sts after pieces are joined. On page 4, for the second Back and Fronts schematic measurement from the top, the last 4 measurements should be 57, 61.5, 65.75, 69.75)”. These corrections have been made in rev.07.16.

103 – Killarney Top-Down Pullover: Under Needles, add “size 4 (3.5 mm) circular needle, 24″ long, for neck.” This correction has been made in rev.09.13.

106 – Boston Top-Down Hooded Coat: Under HOOD, Shape Hood, you will shape the left side of the Hood first, then the right side. At the end of the short-row shaping, in the last sentence of the paragraph before Shape Top of Hood, after “Place marker between center sts,” add “remove other markers. Under BODY BAND, on 6th line of first paragraph, change “ending at lower Right Front edge” to “ending at lower Left Front edge”. These corrections have been made in rev.01.14

107 – Rockport Top-Down Shell: Under Yarn on page 1, the yarn should be listed as Light worsted/DK weight, not worsted weight. Under Back, the instructions under Shape Neck for the RIGHT and LEFT SIDES are reversed. The RIGHT SIDE neck shaping should read as follows: “Next Row (RS): K1, M1-R, knit to end. Purl 1 row. CO 2 sts at beginning of next 2 RS rows – 12 (14, 16, 17, 21, 24, 25, 28, 30, 29, 30) sts. Purl 1 row. Break yarn, place sts on waste yarn, and set aside.” The LEFT SIDE neck shaping should read as follows: “Next Row (RS): Knit to last st, M1-L, k1. Purl 1 row. CO 2 sts at end of next 2 RS rows – 12 (14, 16, 17, 21, 24, 25, 28, 30, 29, 30) sts. Purl 1 row.” These corrections have been made in rev.09.13.

108 – Bristol Top-Down Cardigan: On page 1, under Finished Measurements, third size should be be 36″. Under Yarn, yarn used is DK/Light Worsted weight. Yarn used was Plymouth Yarn DK Merino #1017 Cilantro. On page 2, under Back, first sentence should read as follows: “With RS of Back Collar facing, using longer circ needle, CO 12 (15, 16, 18, 21, 24, 25, 26, 27, 27, 29) sts for left shoulder; working along long unmarked edge of Back Collar (not along edge with slipped sts), slip 1 purlwise from first Collar dpn, pick up and knit 46 (46, 46, 48, 48, 48, 48, 50, 50, 50, 50) sts to next Collar dpn for center neck, slip 1 purlwise from dpn; CO 12 (15, 16, 18, 21, 24, 25, 26, 27, 27, 29) sts for right shoulder – 72 (78, 80, 86, 92, 98, 100, 104, 106, 106, 110) sts.” On page 2, line 7 in second paragraph under “Shape Neck and Armholes”, “purl 1 row” should read “work even for 1 row.” On page 3, third line under Shape Hips, the last word in that line should be LLI, not M1-R. These corrections have been made in rev.03.14.

115 – Boulder Top-Down Hoodie: On page 2, under Back, you should work even until piece measures 6.5 (6.25, 6.25, 6.75) (6.75, 6.5, 6.75) (6.25, 5.75, 6, 5.5)” from the beginning before shaping the armholes. For the Front, under JOIN SIDES, work even until piece measures 6.5 (6.25, 6.25, 6.75) (6.75, 6.5, 6.75) (6.25, 5.75, 6, 5.5)” from the beginning before shaping the armholes. On page 3, under SHAPING INFORMATION (lower right corner), the corrected armhole shaping information is as follows: Armhole Shaping: 6 (8, 12, 14) (16, 18, 18) (22, 26, 26, 28) rows; 1 (1.25, 1.75, 2) (2.25, 2.75, 2.75) (3.25, 3.75, 3.75, 4.25)”. These corrections have been made in rev.06.18.

117 – Belmont Top-Down Coat: Yarn weight symbol at top right of page 1 should be a 5 BULKY. On page 3, under Shape Sleeve, Single Decrease Rnd should be worked as follows: K1, ssk, knit to last 3 sts, k2tog, k1. Under Customize Your Fit, Under Sleeve Shaping, “increasing the number of rnds between increase rnds” should read “increasing the number of rnds between decrease rnds.”